New-buck-corporation FS 21 Manual de usuario

MODEL FS 21 NON-CATALYTIC UNIT FEATURES PREPARATIONS INSTALLATION OPERATION MAINTENANCE SAFETY Buck Stove

Page 8 HOW TO LOCATE CHIMNEY EXIT AND INSTALL Residential Installation B. Vertical Wall Exit using (6" Single Wall minimum 24 ga. blued

Page 9 B. Vertical wall exit using (6" Single wall minimum 24 ga. blued or black pipe with elbow and any listed 2100° UL 103 HT. TYPE Chimney

Page 10 HOW TO LOCATE CHIMNEY EXIT AND INSTALL Residential and Mobile Home Installation C. Vertical Exit using (6" DVL Close Clearance pip

Page 11 NOTE: All clearances are to combustibles with optional close clearance shields and pipe shield, using DVL Close Clearance pipe, and minimum

Page 12 HOW TO LOCATE CHIMNEY EXIT AND INSTALL Residential and Mobile Home Installation D. Vertical Wall Exit using (6" DVL Close Clearance

Page 13 D. Vertical wall exit using (6" DVL Close Clearance pipe with elbow and any listed 2100° UL 103 HT. TYPE Chimney and Listed 2100° UL

Page 14 OUT SIDE AIR INSTALLATION Select an installation location that will give the best airflow from the front of the heater to the remainder of

Page 15 UNDER SIDE OF MOBILE HOME FLOOR Figure 10B OUTSIDE AIR DUCT FLOOR PROTECTOR PAD OUTSIDE AIR DUCT THROUGH FLOOR WHEN MOBILE HOME IS NOT UND

Page 16 FINAL CHECK 1. Recheck the specified clearances. 2. Remove all foreign material from the firebox area. 3. Open the primary air draft. 4.

Page 17 ALCOVE INSTALLATION AND CLEARANCES Select an installation location that will give the best airflow from th

Page 18 Floor Protection: Floor protection must be 3/8” minimum thickness non-combustible material or equivalent. How to use alternate materials and

Page 19 HOW TO LOCATE CHIMNEY EXIT AND INSTALL Alcove Installation Vertical Exit using (6" DVL Close Clearance pipe and any Listed 2100° UL 10

Page 20 ALCOVE INSTALLATION AND CLEARANCES Vertical exit using (6" DVL Close Clearance pipe, and any listed 2100° UL 103 HT. TYPE Chimney).

Page 21 FINAL CHECK 1. Recheck the specified clearances. 2. Remove all foreign material from the firebox area. 3. Open the primary air draft. 4.

Page 22 Installation of (Optional) Close Clearance Shields and Pipe Shield 1. Taking close clearance side shields, hold up to side of stove leav

Page 23 OPERATION This section of the manual is to help you get the maximum efficiency and maximum smoke (particulate) reduction from your heate

Page 24 ASH REMOVAL INSTRUCTIONS (3) DUMP CHANNEL. SWEEP ASHES INTO ASHASH DUMP TOP LID ANDREAR OF HEATER. OPENDUMP TOP LID IN RIGHTFIRE BOX. LOCA

Page 25 OPTIONAL MOTOR ASSEMBLY KIT INSTALLATION INSTRUCTIONS STEP 1. REMOVE ACCESS DOOR PANEL LOCATED AT BOTTOM OF UNIT. YOUR MOTOR ASSEMBLY CO

Page 26 STEP 1 STEP 2 STEP 3 WIRE DIAGRAM

Page 27 1 - MOTOR (NON-CAT) 1 - MOTOR BRACKET 6 - #10 - 16 X 1/2” HEX HEAD 1 - #6 - 32 X 1/2” SLOT HEAD SCREW 5 - 1/8” X 1” BLACK FLAT GASK

TABLE OF CONTENTS Important Instructions ...

Page 28 WOOD HEATER SAFETY Certain safety hazards are inherent in any wood heater installation. You should be aware of these so that a safe an

Page 29 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Sluggish Heater Obstruction in chimney Check for and remove obstruction Wet or uns

Page 30 NEW BUCK CORPORATION (NBC) "LIMITED WARRANTY" FOR THE BUCK STOVE PLEASE READ THIS WARRANTY CAREFULLY PRODUCTS COVERED This warra

If for any reason you are dissatisfied with the suggested procedures, you may contact us in writing at: New Buck Corporation Customer Service D

Page 2 INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS MODEL FS 21 READ THIS FIRST IMPORTANT INSTRUCTIONS  The New Buck Corp. non-cataly

Page 3 INTRODUCTION Your new MODEL FS 21 is a non-catalytic unit designed to meet the most stringent emissions standards without the use of a cata

Page 4 RESIDENTIAL / MOBILE FREESTANDING INSTALLATION AND CLEARANCES Select an installation location that will give the best airflow fro

Page 5 Floor Protection: Floor protection must be 3/8” minimum thickness non-combustible material or equivalent. How to use alternate materials and

Page 6 PREPARING THE ROOM HEATER LOCATION 1. Select an installation location that will give the best airflow from the front of the heater to the re

Page 7 A. Vertical exit using (6" Single wall minimum 24 ga. blued or black pipe and any listed 2100° UL 103 HT. TYPE Chimney) Without o